£400 + VAT per working drive, any CCTV recorderSend the drive, not the recorder · 5 working days · paid upfrontSwitch it off, then call:0800 6890668
CCTV·DRCCTV Data Recovery 0800 6890668 Send a drive
CCTV·DR / What happened / The recorder was factory reset

Restore defaults · reset button · reset to clear a password · settings gone, recordings maybe not · overwrite and schedule back to default · £400 + VAT

The recorder was factory reset. A reset is aimed at the settings. Whether it touched the recordings depends on the model and on what else was ticked.

Factory resets are done for ordinary reasons: a forgotten password, a recorder that has become sluggish, a change of owner, an engineer's first resort. A reset restores the recorder's configuration to the state it left the factory in. The configuration lives in the recorder's own memory, not on the hard drive, so on many models the recordings are untouched and reappear in playback once the recorder restarts. On others the reset screen includes a format, or the recorder treats its drive as new afterwards. And on all of them the defaults may differ from how the system was set up, so that it records differently from then on.

Binary image first, original untouchedAll video processed from the imageDrive only, not the recorder£400 + VAT per working drive, paid upfront

Switch the recorder off first. Then tell us the make, what happened and the date you need: we say what is realistic before you pay anything
0800 6890668

What can and cannot come back.

Can be recoveredRecordings left on the drive by a reset that cleared only the settings, or by one that formatted and was then stopped
FromA binary image examined for the recorder's video blocks
Cannot be recoveredFootage recorded over since the reset

What was done, and what it wrote to the drive.

What was doneWhat it wrote to the driveWhat usually survivesWhat the bench does
Settings-only resetNothingEverythingOften no recovery is needed: export from the recorder
Reset with 'format HDD' tickedNew indexThe video blocks, at firstAs for a format
Reset, then the setup wizard formatted the driveNew indexThe video blocks, at firstAs for a format
Reset changed recording to motion-only or offLess new video, or noneOld footage lasts longerOld footage read; gap explained
Reset changed the clockNew video carries a different timeEverythingTwo time bases; allow for it when viewing
Cameras not re-added after resetNothing new recordedEverything, frozen at the resetRead in full

What to do now, in order.

  1. Look, without changing anythingAfter a reset, open playback and see whether earlier days are marked.
  2. If they are, export nowTo a USB stick, the period you need, before the recorder overwrites or anyone resets again.
  3. If the setup wizard asks to format, declineOr switch off. A wizard's 'initialise HDD' step is a format.
  4. If the old days have gone, switch offAnd remove the drive. Treat it as a formatted drive.
  5. Note what was reset and howMenu option, pinhole button, or a maker's tool. And the date and time.

Do not

  • Do not run the setup wizard through on autopilot.
  • Do not reset a second time to 'do it properly'.
  • Do not assume a reset is harmless because the box did not mention recordings.
  • Do not leave a freshly reset recorder running for days before checking playback.
  • Do not change the clock on a recorder whose footage may be needed; note the error.

In more detail.

Settings and recordings are kept apart

A recorder holds its configuration in flash memory on its main board. The hard drive holds the video and the structures that index it. A reset to defaults rewrites the first and need not touch the second. That is why footage so often survives a reset, and why a recorder with no drive fitted can still be configured. The complication is what the recorder does next. Some models run a first-time setup wizard after a reset, and the wizard treats the drive as it would in a new installation: it offers to initialise it. Accepting that step is what removes the recordings from view.

The defaults may not suit you

Even a reset that leaves every recording in place changes the recorder's behaviour. Overwrite may default to on where it was off, in which case old footage starts to be replaced, or to off where it was on, in which case the recorder will fill and stop. Recording may default to motion-only. Cameras connected over the network may need to be added again and will record nothing until they are. The clock may fall back to a default time zone. Each of these has produced a customer who found, months later, that the recorder had kept nothing since the reset.

When recovery is needed and when it is not

If the old recordings are still listed after the reset, the cheapest course is the recorder's own export, and this service is not required. If playback is empty, the reset included a format in one form or another, and the position is the one described for formatted drives: the video is still largely on the disk and is being replaced for as long as the recorder runs. If you cannot tell, because the password or the menus are now a puzzle, switch the recorder off and take the drive out. Nothing is lost by doing so, and the image will show which it was.

Sources
  1. Han, Jeong and Lee, 'Analysis of the HIKVISION DVR File System', ICDF2C 2015 (Springer LNICST) — eudl.eu/pdf/10.1007/978-3-319-25512-5_13
  2. Hikvision USA support, 'What do I do after I install a new hard drive?' — supportusa.hikvision.com/support/solutions/articles/17000129501-what-do-i-do-after-i-install-a-new-hard-drive-
  3. Hikvision USA support, tips on hard disk settings on Hikvision recorders — supportusa.hikvision.com/support/solutions/articles/17000130208-do-you-have-any-tips-regarding-hard-disk-settings-on-hikvision-recorders-
  4. Lorex D861 series manual, troubleshooting table — www.lorextechnology.com/downloads/security-dvr/D861/Manual/WEB/EN/LX500961.xml.html
  5. Rzayeva et al., 'Automated Forensic Recovery Methodology for Video Evidence from Hikvision and Dahua DVR/NVR Systems', Information 2025, 16(11):983 — www.mdpi.com/2078-2489/16/11/983

Quotations were checked against the sources listed in November 2026. Makers change their support pages and manuals; follow the links for the current wording. Research figures are the authors' results on their own drives. No maker, regulator or police body listed is connected with this site.

Asked after this happens.

Does a factory reset delete CCTV footage?

Not necessarily. It resets settings. On some models it also offers a format, and the setup wizard afterwards may initialise the drive.

Playback is empty after the reset. Is the footage recoverable?

Usually, if the recorder has not run for long since. Switch it off and remove the drive.

What does it cost?

£400 + VAT for one drive, paid upfront and non-refundable.

Switched off. Drive out. Then tell us what happened.

Tell us the recorder, what happened and the date you need. The reply, inside a working day, says whether the footage is likely to be on the drive. Nothing is charged for that. Recovery is £400 + VAT per working drive, paid upfront and non-refundable; failing or damaged drives cost more and are quoted first.