£400 + VAT per working drive, any CCTV recorderSend the drive, not the recorder · 5 working days · paid upfrontSwitch it off, then call:0800 6890668
CCTV·DRCCTV Data Recovery 0800 6890668 Send a drive
CCTV·DR / The recorder said / 'Uninitialized' and 'format the HDD'

HDD status: Uninitialized · 'initialize the drive, select yes/ok' · Init · Format · the index, not the video · switch off first · £400 + VAT

'Uninitialized' and 'format the HDD'. The recorder is offering to forget everything on the drive. Decline, switch off, and take the drive out.

Recorders show a status for each hard drive. 'Normal' means the recorder recognises its own layout on the disk. 'Uninitialized' means it does not, and it will not record until the drive is initialised. On a brand-new disk that is expected. On a disk that held a month of recordings yesterday, it means the structures at the start of the disk have been damaged, by a power cut, a failing sector or a spell in another device. The recorder cannot tell the difference between the two cases and offers the same button for both. Pressing it turns 'Uninitialized' into 'Normal' by writing a fresh, empty index.

Binary image first, original untouchedAll video processed from the imageDrive only, not the recorder£400 + VAT per working drive, paid upfront

Switch the recorder off first. Then tell us the make, what happened and the date you need: we say what is realistic before you pay anything
0800 6890668

ON SCREEN● ALARM
Uninitialized
Quoted from the makerHikvision HDD status. Hikvision's manuals describe initialising: 'the status of the HDD will switch from Uninitialized to Normal'

What can and cannot come back.

Can be recoveredVideo blocks still on the disk, with times and channels rebuilt
FromThe published finding that initialising resets the index, not the video
Cannot be recoveredBlocks recorded over after an initialise

Why it says that.

The third column is the question that matters most: if the recorder stopped recording when the message began, nothing after that point exists.

Likely causeHow to tellWas it still recording?What the bench does
Power cut during a writeStatus changed after a cutNo, until initialisedStructures repaired on the image; video read
Bad sectors at the start of the diskStatus changed with no event; drive may be noisyNoImaged round the damage; blocks parsed directly
Drive was in a PC or another recorderSomeone 'had a look'NoDepends what was written to it there
Init pressed, recorder then switched offStatus back to Normal, playback emptyBriefly, over the oldest footageMost of the video is normally still present
Init pressed, recorder left runningNormal, with new recordings onlyYes, over the oldWhat remains shrinks with every day
New driveJust fittedNot yetNothing to recover; initialise it

What to do, in order.

  1. Do not answer yesIf a prompt is on screen, leave it. Do not select OK, Init or Format.
  2. Switch the recorder offAt the wall. An uninitialised drive is not being recorded to, so nothing is lost by stopping.
  3. If Init was already pressed, switch off nowThe recorder is recording again from the start of the disk. Minutes matter more than they did.
  4. Remove the driveLabel it with the date and what was done.
  5. Tell us exactly what was pressed and whenAnd roughly how long the recorder ran afterwards. It decides how much of the old footage is left.

Do not

  • Do not initialise 'to see if the footage comes back'. It will not.
  • Do not let an engineer initialise it to get the system working; fit a new drive instead.
  • Do not run the recorder after an initialise.
  • Do not initialise the drive in Windows either.
  • Do not try a second recorder of the same make.

The message, in more detail.

What initialising writes

The 2015 study of the best-known recorder format looked at exactly this. It found that system initialisation resets the time recorded in the master sector, restores the logs to zero and initialises the index of video blocks. It also found that, initialisation notwithstanding, video could still be identified by reading the data blocks. The recorder forgets where everything is; the disk does not. That is the difference between a recorder's playback screen, which now shows nothing, and a forensic image, which shows a disk still largely full of last month.

The clock that starts when Init is pressed

An initialised recorder goes straight back to work. It begins recording into the first blocks of the disk, and the first blocks hold the oldest footage. On a drive that had been looping, the oldest footage is whatever was about to be overwritten anyway, so the earliest loss is the material furthest from the present. A recorder run for a few hours after an initialise typically costs a few hours of the oldest days. One left for a fortnight may have replaced half the disk. The incident you want is usually recent, and so among the last to go, but only if someone switches the recorder off.

Keeping the system working

A business cannot always leave its cameras unrecorded while a drive is away. The answer is a second drive. Take out the drive that holds the footage, fit a new one, and initialise that. The recorder is satisfied, recording resumes, and the old drive is untouched. A surveillance-rated drive of the same size costs far less than the footage is worth to anyone who needs it. Hikvision's instruction that the unit 'should ask to initialize the drive, select yes/ok' is the right answer for the new drive and only for the new drive.

Sources
  1. Han, Jeong and Lee, 'Analysis of the HIKVISION DVR File System', ICDF2C 2015 (Springer LNICST) — eudl.eu/pdf/10.1007/978-3-319-25512-5_13
  2. Hikvision USA support, 'What do I do after I install a new hard drive?' — supportusa.hikvision.com/support/solutions/articles/17000129501-what-do-i-do-after-i-install-a-new-hard-drive-
  3. Hikvision USA support, 'Audible Warning is saying there is a HDD error' — supportusa.hikvision.com/support/solutions/articles/17000128918-audible-warning-is-saying-there-is-a-hdd-error
  4. Milesight support, 'NVR failed to record' — support.milesight.com/support/solutions/articles/69000860504--nvr-record-nvr-failed-to-record
  5. Rzayeva et al., 'Automated Forensic Recovery Methodology for Video Evidence from Hikvision and Dahua DVR/NVR Systems', Information 2025, 16(11):983 — www.mdpi.com/2078-2489/16/11/983

Quotations were checked against the sources listed in November 2026. Makers change their support pages and manuals; follow the links for the current wording. Research figures are the authors' results on their own drives. No maker, regulator or police body listed is connected with this site.

Asked about this message.

I pressed Init. Have I lost everything?

Probably not. Initialising clears the index; the video is overwritten later, as the recorder records. Switch it off now.

Why does the recorder show nothing in playback afterwards?

Because playback reads the index, and the index is now empty. The video is found by reading the disk itself.

What does it cost?

£400 + VAT for one drive, paid upfront and non-refundable.

Switched off. Drive out. Then tell us what happened.

Tell us the recorder, what happened and the date you need. The reply, inside a working day, says whether the footage is likely to be on the drive. Nothing is charged for that. Recovery is £400 + VAT per working drive, paid upfront and non-refundable; failing or damaged drives cost more and are quoted first.