£400 + VAT per working drive, any CCTV recorderSend the drive, not the recorder · 5 working days · paid upfrontSwitch it off, then call:0800 6890668
CCTV·DRCCTV Data Recovery 0800 6890668 Send a drive
CCTV·DR / The recorder said / 'HDD Error' and a recorder that will not stop beeping

HDD Error · continuous beeping · exception alarm · status 'Abnormal' · was it still recording? · do not format · £400 + VAT

'HDD Error' and a recorder that will not stop beeping. The beep means the recorder cannot write. The first question is how long it has been unable to.

A recorder that beeps without stopping and shows 'HDD Error' has raised what the makers call an exception: it tried to write video to the hard drive and could not. The cause may be a failing disk, a cable shaken loose, a power supply that can no longer start the drive, or damage to the structures the recorder keeps at the start of the disk. Whichever it is, two things follow. The recorder has probably recorded nothing since the alarm began, so the date it began matters. And the remedy the maker's help page offers is the one that removes your recordings: 'If the status remains then format the HDD.'

Binary image first, original untouchedAll video processed from the imageDrive only, not the recorder£400 + VAT per working drive, paid upfront

Switch the recorder off first. Then tell us the make, what happened and the date you need: we say what is realistic before you pay anything
0800 6890668

ON SCREEN● ALARM
HDD Error
Quoted from the makerHikvision manuals list: 'HDD Error: Writing HDD error, unformatted HDD, etc.' The audible warning is the recorder's exception alarm

What can and cannot come back.

Can be recoveredFootage recorded up to the moment the error began
FromA binary image of the drive, made with equipment that reads round bad areas
Cannot be recoveredAnything from the days the recorder sat beeping and not recording

Why it says that.

The third column is the question that matters most: if the recorder stopped recording when the message began, nothing after that point exists.

Likely causeHow to tellWas it still recording?What the bench does
Failing hard driveClicking, slow start, the error returns after reseatingNo, from the first failed writeImaged slowly on hardware made for failing drives
Loose SATA or power leadError appeared after the recorder was moved or knockedNo, while disconnectedDrive is usually healthy and reads in full
Weak power adapterDrive spins up and stops; error comes and goesIntermittentlyDrive imaged on a proper supply
Damaged index after a power cutError began with a cut or a stormNo, until 'fixed' by formattingVideo read directly; index rebuilt on the copy
Drive full, overwrite offMessage may read 'HDD Full'No, since it filledEverything up to that date is normally present
Wrong or new drive fittedError since a drive was changedNever, on that driveFind the old drive

What to do, in order.

  1. Silence the alarm without touching the diskThe beep can be muted in the exception settings or by switching the recorder off. Do not go into the HDD or storage menu.
  2. Note what the screen saysThe exact words, and the HDD status if it is shown: Normal, Abnormal, Uninitialized, Sleeping or No HDD.
  3. Find out when it startedAsk whoever is on site when the beeping began. That is roughly when recording stopped.
  4. Power off and remove the driveUnplug the recorder, open it, disconnect the two leads from the drive and lift it out.
  5. Tell us the datesThe date the error began and the date of what you need. If the second is later than the first, the footage was probably never recorded.

Do not

  • Do not choose Format or Init to stop the beeping.
  • Do not keep powering a clicking drive on and off.
  • Do not fit the drive in another recorder to test it.
  • Do not replace the drive and throw the old one away.
  • Do not assume it kept recording because the cameras still showed live pictures.

The message, in more detail.

What the recorder is complaining about

Recorders watch for a short list of faults and sound an alarm for each: disk full, disk error, network lost, and so on. Hikvision's manuals define the disk one as 'Writing HDD error, unformatted HDD, etc.' Its own support article goes on to say which alarm it recommends leaving switched on: the HDD error warning, because that is the one that means footage is no longer being kept. In practice many owners mute the beep, or the recorder sits in a cupboard where nobody hears it, and the error stands for weeks.

Why not format

Hikvision's support page for the audible warning says of the 'Abnormal' status: 'power off the NVR and reseat the cabling of the NVR. If the status remains then format the HDD if error does not clear the HDD will need to be replaced.' There is no mention of the recordings. Formatting does make many errors go away, because it writes fresh structures. It also makes the recorder treat the disk as empty and begin recording at the start. If the drive is failing, the format may not even complete, and the attempt adds wear to a disk that needed to be read once, carefully.

The date the beeping began

Because a recorder in error has usually stopped recording, the most useful fact you can supply is when the alarm started. If a break-in happened on the 14th and the staff remember the beeping from the 9th, the 14th is not on the drive, and no recovery will produce it. If the beeping began on the 15th, the 14th was among the last things recorded and is very likely recoverable. Where nobody knows, the image settles it: the recorder's own logs, where they survive, record the error and the last successful write.

Sources
  1. Hikvision USA support, 'Audible Warning is saying there is a HDD error' — supportusa.hikvision.com/support/solutions/articles/17000128918-audible-warning-is-saying-there-is-a-hdd-error
  2. Hikvision USA support, tips on hard disk settings on Hikvision recorders — supportusa.hikvision.com/support/solutions/articles/17000130208-do-you-have-any-tips-regarding-hard-disk-settings-on-hikvision-recorders-
  3. Han, Jeong and Lee, 'Analysis of the HIKVISION DVR File System', ICDF2C 2015 (Springer LNICST) — eudl.eu/pdf/10.1007/978-3-319-25512-5_13
  4. Dragonas, Lambrinoudakis and Kotsis, 'IoT forensics: Exploiting unexplored log records from the HIKVISION file system', J Forensic Sci 2023; 68:2002-2011 — doi.org/10.1111/1556-4029.15349
  5. Yang, Li and Wu, 'Basic Principle and Application of Video Recovery Software for Dahua and Hikvision Brand', SHS Web of Conferences 14 (2015) — doaj.org/article/70994b3b90834c3689cabf8815611700

Quotations were checked against the sources listed in November 2026. Makers change their support pages and manuals; follow the links for the current wording. Research figures are the authors' results on their own drives. No maker, regulator or police body listed is connected with this site.

Asked about this message.

Has it been recording while it beeped?

Usually not. The error means writes are failing. The date the beeping started is roughly the date recording stopped.

The manufacturer says to format. Why not?

Because a format clears the index and the recorder then records over the old footage. It cures the recorder at the expense of the recordings.

What does recovery cost?

£400 + VAT for one drive, paid upfront and non-refundable, including when the answer is that the day you need was never recorded.

Switched off. Drive out. Then tell us what happened.

Tell us the recorder, what happened and the date you need. The reply, inside a working day, says whether the footage is likely to be on the drive. Nothing is charged for that. Recovery is £400 + VAT per working drive, paid upfront and non-refundable; failing or damaged drives cost more and are quoted first.